Fanny Littmarck | January 13, 2014
It’s easy to navigate from place to place thanks to GPS, but what about once you actually get there — what about navigating indoors? From venues of leisure to buildings in flames, there are many situations where indoor location tracking is useful. GPS technology does not work inside buildings, but there are now other methods under development that will make indoor navigation possible as well.
Lexi Carver | January 10, 2014
Charged particles (such as ions and electrons) are susceptible to electromagnetic fields that exist in the space they occupy. Macroscopic and microscopic particles (dust, pollutants, etc.) are primarily susceptible to forces due to the background fluid (liquid or gas) in which they reside. Particles may also interact amongst each other, or influence the surrounding fields. For systems such as particle accelerators, aerosol distributors, and filtration devices, it can be helpful to calculate particle trajectories or know where the collisions and […]
Walter Frei | January 8, 2014
When you are working with foreign CAD data, such as files in STEP or IGES file formats, you may think that you need to re-import a new CAD file and start your modeling over from scratch if you want to study a change in size or shape. But, in fact, you can modify the geometry that you’ve imported with some clever usage of the Deformed Geometry interface in COMSOL Multiphysics. Here, we will look at how this can be done.
Nicolas Huc | January 6, 2014
In this blog post we will explain the concept of conjugate heat transfer and show you some of its applications. Conjugate heat transfer corresponds with the combination of heat transfer in solids and heat transfer in fluids. In solids, conduction often dominates whereas in fluids, convection usually dominates. Conjugate heat transfer is observed in many situations. For example, heat sinks are optimized to combine heat transfer by conduction in the heat sink with the convection in the surrounding fluid.
Mads Herring Jensen | January 2, 2014
I recently had the pleasure of preparing a small contribution to the 166th Meeting of the Acoustical Society of America (Fall 2013) together with Wade Conklin and Jordan Schultz from Knowles Electronics. Wade presented our paper entitled “Characterization of a microelectromechanical microphone using the finite element method”. The work consisted of implementing a virtual prototype of a Knowles MEMS microphone (the SPU0409LE5H microphone, see picture below) using COMSOL Multiphysics.
Chris Pinciuc | December 31, 2013
Jennifer Segui | January 9, 2014
Spectroscopic imaging has been used for decades to map the chemical composition of material surfaces with atomic-scale resolution. In order to achieve adequate chemical specificity and spatial resolution during imaging, both the material sample and the imaging system are placed under high or ultra-high vacuum (UHV). In practice, materials are often used outside of vacuum environments and therefore it is also necessary to evaluate their surface properties at higher or ambient pressure. Differential pumping is the key to designing vacuum […]
Lexi Carver | January 7, 2014
An RF MEMS switch is an electromechanical component found in RF systems. It usually consists of a micromechanical bridge or cantilever, a substrate, and an electrode or dielectric layer. These devices can switch at RF frequencies and tend to have high isolation, i.e. power loss when the switch turns off; low insertion loss (loss of signal power when the switch is on), and extremely low (almost zero!) power consumption. Let’s take a look at how you can use COMSOL Multiphysics […]
Fanny Littmarck | January 3, 2014
Before conducting certain blood sample analyses, researchers need to separate the red blood cell particles from the blood plasma. Using lab-on-a-chip (LOC) technology, red blood cell separation can be achieved via magnetophoresis, i.e. motion induced by magnetic fields. Since the magnetic permeability of the particles is different from the blood plasma, their trajectory can be controlled within the flow channel of the LOC device and thereby separated out from the fluid.
Mateusz Stec | January 1, 2014
Computer aided engineering (CAE) helps us understand how mechanical systems work before they are physically realized. In order to properly reflect the reality, we continuously increase the modeling complexity when we simulate, validate, or optimize our applications. A simple technique to improve a model is to increase the number of finite elements that in turn create more evaluation points. The hardware and simulation time, however, may limit the size of the model, and other solutions are necessary — such as […]
Alexandra Foley | December 30, 2013
Not too long ago, my colleague Jennifer wrote a blog post about the Cross Cancer Institute, and the research being conducted there into the design of a new device for treating cancerous tumors. The device, known as the Linac-MR, is revolutionary due to its ability to both image and treat cancer cells simultaneously — a capability that had previously been regarded as near impossible due to the conflicting physics interactions involved. Such a device would allow for extremely precise radiation […]