T. Hutter, N. Bamiedakis, and S. Elliott
Department of Chemistry, University of Cambridge, UK
Centre for Advanced Photonics and Electronics, Engineering Department, University of Cambridge, UK
The finite-element method (FEM) (COMSOL RF Module) has been employed for modal analyses of porous silicon (PSi) waveguides composed of a guiding layer of low porosity (high refractive index) on a cladding layer with higher porosity (lower refractive index). These can be made by switching the current density from a lower to a higher value during the electrochemical etching process. The ...
C. Siegel[1,2], G. Bandlamudi[1,2], P. Beckhaus, and A. Heinzel[1,2]
Zentrum für BrennstoffzellenTechnik (ZBT), Duisburg, Germany
University of Duisburg-Essen, Duisburg, Germany
This study highlights the possibility of using COMSOL Multiphysics for solving large scale PEM fuel cell stack models in the order of several million degrees of freedom (DOF). First, different gas flow channel configurations are solved in order to highlight the fluid flow and pressure behaviour. For these models, the full 3D Navier-Stokes equations are solved. It is seen that the amount of fluid ...
Y. Beauregard, M. Gobian, and F. Garisto
University of Western Ontario, London, ON, Canada
Nuclear Waste Management Organization, Toronto, ON, Canada
In the Canadian concept for a deep geological repository for used nuclear fuel, the used fuel bundles are placed in containers consisting of an inner steel vessel surrounded by a copper shell. The filled containers are placed in excavated tunnels or boreholes and surrounded by a compacted bentonite clay buffer material. In the event of container failure, the rate of migration of radionuclides ...
Chinese Academy of Sciences, Dalian Institute of Chemical Physics, Beijing, China
We studied the transient characteristics of PEMFC and water transport during PEMFC start-up, concerning the following aspects: Effect of air stoichiometry change on transient behavior of PEMFC, Transient behavior of water transport during PEMFC start-up, and high temperature PEMFC modeling.
I. Rodriguez, and J. L. Munoz
The field quality requirements of most particle accelerator magnets are very tight and, therefore, very precise simulations are needed to accurately calculate these devices. CERN\'s ROXIE code is widely used as a reference software to calculate normal conducting and superconducting magnets for particle accelerator applications. ROXIE uses the full vector potential coupled to the BEM-FEM ...
Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method
M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic properties of CNT based polymer composites are evaluated using a square Representative Volume Element (RVE) in ...
A. Helfrich-Schkarbanenko, M. Mitschele, S. Ritterbusch, and V. Heuveline
Engineering Mathematics and Computing Lab (EMCL), Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
Institute for Analysis, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
We consider a 3D boundary value problem arising in electrostatics. The potential is stimulated by current sources placed on a cross-section S of the domain. In many applications it is sufficient to know the potential in S. So, one is interested in an appropriate 2D model taking into account that the solution depends on the dimension of the domain. The idea is to find a corresponding 2D ...
P. Pattanaik, S. K. Kamilla, D. P. Das, S. K. Pradhan
MEMS Design Center, Institute of Technical Education & Research (ITER), Sikhya ‘O’ Anushandhan University, Bhubaneswar, Odisha, India
Process Engineering and Instrumentation Lab, Institute of Minerals and Materials Technology (IMMT), Bhubaneswar, Odisha, India
Dept of ECE, Hi-Tech Institute of Technology, Khurda, Odisha, India
This paper describes the design of an ultrasonic transducer using different lead free piezo-electric materials and evaluates their performance with different glucose levels in the human blood. COMSOL Multiphysics 4.2a was used for the simulation study using 2D axis symmetric model of piezoelectric transducer which was designed with lead free piezoelectric materials such as Barium Sodium Niobate ...
Reliability Enhancement of Bio MEMS based Cantilever Array Sensors for Antigen Detection System using Heterogeneous Modular Redundancy
L. S. Sundharam
Kumaraguru college of Technology, Coimbatore, Tamil nadu, India
The objective of the work is to propose a reliability enhancement model for antigen detection system (ADS) using bio MEMS based cantilever array sensors using heterogeneous modular redundancy technique. The reliability of the ADS is expressed in terms of the constituent sub systems which are heterogeneous not only in their respective structures and behaviors but also in their forms. The possible ...
Department of Mechanical Engineering, Kun Shan University of Technology, Tainan, Taiwan
Multiphysics simulation has been used extensively in our research for fluid flow and heat transfer applications. Our projects include: simulation of fluid dynamics in an active liquid heat sink for CPU cooling, impeller design for a pipe flow generator with computational fluid dynamics (CFD), investment casting with plastic rapid prototype patterns, phase change materials with rapid prototyping ...