Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Reliability Enhancement of Bio MEMS based Cantilever Array Sensors for Antigen Detection System using Heterogeneous Modular Redundancy

L. S. Sundharam[1]
[1]Kumaraguru college of Technology, Coimbatore, Tamil nadu, India

The objective of the work is to propose a reliability enhancement model for antigen detection system (ADS) using bio MEMS based cantilever array sensors using heterogeneous modular redundancy technique. The reliability of the ADS is expressed in terms of the constituent sub systems which are heterogeneous not only in their respective structures and behaviors but also in their forms. The possible ...

Numerical Simulations of Radionuclide Transport through Clay and Confining Units in a Geological Repository using COMSOL

J. Hansmann[1], M. L. Sentis[1], B. J. Graupner[1], A.-K. Leuz[1], C. Belardinelli[2]
[1]Swiss Federal Nuclear Safety Inspectorate (ENSI), Brugg, Switzerland
[2]Kantonsschule Solothurn, Solothurn, Switzerland

Introduction: The sectoral plan that defines the procedure and criteria of site selection for deep geological repositories for all categories of waste (high-level and low- and intermediate-level waste) in Switzerland started in 2008 and will last for about ten years. ENSI (Swiss Nuclear Safety Inspectorate) is in charge of reviewing the proposals and safety assessments for geological ...

A study on Spray Drying in Food Industry

S. Singh[1], N. Baheti[1], A. Tiwari[1]
[1]Institute of Engineering & Science, IPS Academy, Indore, Madhya Pradesh, India

Spray drying is a common drying technique in food industries to convert liquid to powder form. A good understanding on the dynamic behavior of the process is important to ensure proper control. The aim of this study is to develop empirical models for spray drying of whole milk powder and orange juice powder. A preliminary study on the effect of several inputs such as inlet air temperature, feed ...

Design of Microfluidic Device for Cellular Experiment Under Controlled Oxygen Tension

K. Funamoto[1], I.K. Zervantonakis[2], R.D. Kamm[2]
[1]Tohoku University, Sendai City, Miyagi, Japan
[2]Massachusetts Institute of Technology

Numerical simulation of oxygen tension was performed to develop a microfluidic device for three-dimensional real-time observation of cellular response under hypoxia. The optimal experimental condition was obtained through investigations of effects of parameters, such as device thickness and flow rates of media and gas, on oxygen tension.

Numerical Modeling of Power Reactors' Fuel Bundles

R. Schmidt[1], T. Yousefi[2], B. Farahbaksh[2], M. Z. Saghir[2]
[1]University of Louisiana at Lafayette, Lafayette, LA, USA
[2]Ryerson University, Toronto, ON, Canada

Fuel bundles in the CANDU (CANada Deuterium Uranium) reactor are designed for heating a pressurized coolant (heavy water) to generate electricity. The designs for the fuel bundles differ based on the number of heating elements. The flow of heavy water over the elements and inside the shell is highly turbulent. In this paper, COMSOL Multiphysics® is used to simulate the heavy water flow ...

Joule Heating in Electroosmotically Driven Circular Constriction Microchannel

U. Sanjay [1], P. Sarith[2], R. Ajith Kumar[1]
[1]Amrita Vishwa Vidhyapeetham, Kollam, Kerala, India.
[2]National institute of Technology, Calicut, Kerala, India.

Liquid transport in lab-on-a-chip (LOC) devices occurs through a microchannel that uses an electroosmotic flow actuation mechanism. This method has a plug-like velocity profile, which is ideal in species transport and in wall-bounded reactions. Under substantial joule heating, it is not possible to maintain a plug-like velocity distribution. My work investigates the effects of joule heating ...

Generation of Lofted NURBS Curves for 3D Model Generation with COMSOL Multiphysics®

R.T. Hart[1]
[1]Department of Biomedical Engineering, The Ohio State University, Columbus, OH, USA

A key challenge to finding quantitative solutions to biological problems is to model the complex 3D geometry of naturally occurring structures. Model generation often starts from serial sections from CT or MRI scans, confocal microscopy, or physical sectioning. In addition, prior to V4 of COMSOL Multiphysics®, there was a "loft" command to allow construction of 3D models from serial sections ...

COMSOL Multiphysics® Model of Canine Elbow for Use in Investigating Medial Coronoid Disease

K. A. Bodnyk[1], G. J. Noble[1], N. Fitzpatrick[2], M. J. Allen[3], K. Stephenoff[1], R. T. Hart[1]
[1]Department of Biomedical Engineering, The Ohio State University, Columbus, OH, USA
[2]Fitzpatrick Referrals, Godalming, Surrey, United Kingdom
[3]Department of Veterinary Medicine, The Ohio State University, Columbus, OH, USA

The elbow joint in dogs constitutes a complex interaction of three bones, the humerus, radius and ulna. Medial coronoid disease (MCD) is a common cause of lameness in dogs, i.e. fracturing of the most prominent portion of the ulnar joint surface driven in flexion and in pivot against both the humerus and the radius. The cause remains unknown, but prior studies suggest joint incongruency as an ...

Optimization of 3D Layered Metal-Dielectric Stacks (MDS) for Near-Field Fluorescence Imaging

P.S. Tan[1], K. Elsayad[2], K. Heinze[1]
[1]Rudolf Virchow Center, University of Würzburg, Würzburg, Germany
[2]Research Institute of Molecular Pathology (IMP), Vienna, Austria

Nano-structures consisting of layered metal-dielectric stacks (MDSs) can be designed to have evanescent transmission and reflection coefficients that oscillate as a function of transverse wavevector and frequency. However, these structures always suffer from the material losses and surface roughness that are detrimental to image reconstruction. As such, we propose an optimized planar anisotropic ...

Towards Optimized Neural Stimulation in a Device for Urinary Incontinence

A.N. Shiraz[1], A. Demosthenous[1]
[1]E&EE Department, University College London, London, United Kingdom

After spinal cord injury (SCI) the functions of the lower urinary tract are often disrupted and may have fatal consequences for the patient. It has been shown that using a transrectal probe developed by Craggs et al., through conditional transrectal stimulation of pudendal nerve, it is possible to treat hyperreflexia in some of the SCI patients. To maximise the efficacy of this type of ...