Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Numerical Simulation of Flow Electrolysers: Effect of Various Geometric Parameters

P. Shukla[1], K. K. Singh[1], P. K. Gupta [1], S. K. Ghosh[1]
[1]Bhabha Atomic Research Centre, Trombay, Mumbai, India

Flow electrolysers find several applications in industry. They are used for production of metals and synthesis of chemicals, gases. Cleaning and preservation of old artifacts, electrolytic refining of metals, electrolytic winning of metals, alkaline water electrolysis, anodization, electrometallurgy, electroplating, electrolytic etching of metal surfaces are other industrial applications of flow ...

Design of Microfluidic Device for Cellular Experiment Under Controlled Oxygen Tension

K. Funamoto[1], I.K. Zervantonakis[2], R.D. Kamm[2]
[1]Tohoku University, Sendai City, Miyagi, Japan
[2]Massachusetts Institute of Technology

Numerical simulation of oxygen tension was performed to develop a microfluidic device for three-dimensional real-time observation of cellular response under hypoxia. The optimal experimental condition was obtained through investigations of effects of parameters, such as device thickness and flow rates of media and gas, on oxygen tension.

Effect of Fluid Conditions on Air-Liquid Interface in Hydrophobic Micro Textured Surface

S. Takahashi[1], S. Ogata[1]
[1]Tokyo Metropolitan University Hachioji City, Tokyo, Japan

We studied the influence of a number of gas-liquid interface on the drag reduction effect by numeric simulation. Level set method was used for an analysis of gas-liquid interface. The analytic model is rectangular channel of height h = 5 micrometer and width w = 20 micrometer with two hydrophobic microstructures in bottom of channel. In this channel, we found that the liquid penetrates in the ...

Resonant Frequency Analysis of Quartz Shear Oscillator

T. Satyanarayana[1], V. Sai Pavan Rajesh[2]
[1]NPMASS Centre, Lakireddy Bali Reddy Autonomous Engineering College, Mylavaram, Andhra Pradesh, India
[2]Lakireddy Bali Reddy Autonomous Engineering College, Mylavaram, Andhra Pradesh, India

The most commonly used type of resonator is the AT-cut, where the quartz blank is in the form of a thin plate cut at an angle to the optic axis of the crystal. This paper reports the modeling of a quartz oscillator for a resonant frequency analysis based on piezoelectric effects. The proposed oscillator consists of a single quartz disc with two electrodes on the top and bottom surfaces of the ...

An Innovative Reactive Transport Modeling Approach for the Chemical Evolution of a HLW Cell in the Callovo-Oxfordian Formation

J. Molinero[1], D. García[1], M. Grivé[1], A. Nardi[1]
[1]Amphos 21 Consulting, Barcelona, Spain

Andra (The French National Radioactive Waste Management Agency) envisages the safe disposal of High-Level Waste (HLW) and Intermediate-Level Long-Lived Waste (IL-LLW) in deep geological storage using a multi-barrier system. To ensure the containment of radioactivity, the principle of storage is based on a clay formation with low permeability, homogeneity and continuity (i.e Callovo-Oxfordian ...

Annealing Furnaces Modelisation for Photovoltaïc Applications

J. Givernaud[1]
[1]EMIX, St Maurice La Souterraine, France

The optimisation of dimensions, materials choice of heaters in annealing furnaces are done with COMSOL Multiphysics® in 2D-axisymetry. Heat losses sources are identified and corrective actions can be taken in function of simulation results. A power saving of more than 50% is achieved thanks to simulations.

Generation of Lofted NURBS Curves for 3D Model Generation with COMSOL Multiphysics®

R.T. Hart[1]
[1]Department of Biomedical Engineering, The Ohio State University, Columbus, OH, USA

A key challenge to finding quantitative solutions to biological problems is to model the complex 3D geometry of naturally occurring structures. Model generation often starts from serial sections from CT or MRI scans, confocal microscopy, or physical sectioning. In addition, prior to V4 of COMSOL Multiphysics®, there was a "loft" command to allow construction of 3D models from serial sections ...

Advancements in Carbon Dioxide and Water Vapor Separations Using COMSOL Multiphysics®

J. Knox[1], R. Coker[1], R. Cummings[1], C. Gomez[1], G. Schunk[1]
[1]NASA, Marshall Space Flight Center, Huntsville, AL, USA

Some NASA efforts are focused on improving current systems that utilize fixed beds of sorbent pellets by evaluating structured sorbents, seeking more robust pelletized sorbents, and examining alternate bed configurations to improve system efficiency and reliability. For the bulk separation of CO2 and H2O, temperature changes due to the heat of adsorption are significant, requiring modeling and ...

Several Benchmarks for Heat Transfer Problems in COMSOL Multiphysics®

S. Titarenko[1]
[1]University of Leeds, Leeds, United Kingdom

Nowadays all branches in modern science and industry tend to solve ever complicating problems. As the result the computational time increases considerably and it become very important to reduce the processing time and use available resources more efficiently. Parallelizing problem proves itself as efficient way to overcome the described problem. In the poster we compare different methods of ...

Modeling Plant Morphodynamics in Predefined COMSOL Multiphysics® Interface

S. Nikolaev[1], A. Trubuil[2]
[1]Institute of cytology and genetics SB RAS, Novosibirsk, Russia
[2]Institut National de la Recherche Agronomique, Jouy-en-Josas, France

We used a predefined COMSOL Multiphysics® interface to imitate biological growth and shape change (morphodynamics). We found a set of parameters that supply observed morphodynamics for an Arabidopsis embryo during its transition from globular to heart stage.