Menu

Discussion Forum

New Discussion
フィルター

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Strange error

Posted 2011/03/05 6:10 GMT-5 Heat Transfer & Phase Change Version 4.0 5 Replies

Muhale Mutshena
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi all

What does this mean?

Only one thread allowed.
Old model cannot be reconstructed. Do Clear Solution to expunge
5 Replies Last Post 2012/11/06 8:03 GMT-5
COMSOL Moderator

Hello Muhale Mutshena

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.

Dulakshi Karunasinghe
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012/02/27 22:04 GMT-5
Did you find a solution for this? I too get the same error.
Did you find a solution for this? I too get the same error.
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012/02/28 1:20 GMT-5
Hi

try a EDIT clear all solution Edit Clear Mesh, File Reset Model, save, reopen COMSOl clean and reload your file. This might do the trick

--
Good luck
Ivar
Hi try a EDIT clear all solution Edit Clear Mesh, File Reset Model, save, reopen COMSOl clean and reload your file. This might do the trick -- Good luck Ivar
Analía Gastón
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012/02/28 13:31 GMT-5
Hi Ivar, i have the same problem, but with your answer I erased the solution, so, this is not the best way to solve this problem...another idea?
Hi Ivar, i have the same problem, but with your answer I erased the solution, so, this is not the best way to solve this problem...another idea?
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012/02/29 0:52 GMT-5
Hi

sorry to hea that, but indeed if you delete a solver you delete the related nodes lower down. The best would be to use a newer veersion of COMSOL 4.0 was really the firs out in the new "costume", the stability of the programme has greatly improved since

--
Good luck
Ivar
Hi sorry to hea that, but indeed if you delete a solver you delete the related nodes lower down. The best would be to use a newer veersion of COMSOL 4.0 was really the firs out in the new "costume", the stability of the programme has greatly improved since -- Good luck Ivar
Akmal
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012/11/06 8:03 GMT-5
Hi all,

it happened after i copy comsol model 4.2 (incl. solution) to another directory.

i'm not sure about it but it can be "reproduced" or "repaired" by send that model to comsol support via some ftp link.

regards
akmal

Hi all, it happened after i copy comsol model 4.2 (incl. solution) to another directory. i'm not sure about it but it can be "reproduced" or "repaired" by send that model to comsol support via some ftp link. regards akmal

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content