アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効なCOMSOLライセンスに関連付けられている COMSOL アクセスアカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
Thin Low Permittivity Gap Comparison
The thin low permittivity gap boundary condition is meant to approximate a thin layer of material with low relative permittivity compared to its surroundings. This boundary condition is available for electrostatic field modeling. This example compares the thin low permittivity gap ... 詳細を見る
Electrical Heating in a Busbar Assembly
This tutorial model of the Joule heating effect in a busbar demonstrates how to synchronize an assembly between Inventor and COMSOL, how to modify the geometry from COMSOL, and how to run a geometric parametric sweep. 詳細を見る
Helicopter Swashplate Mechanism
This model illustrates the operation of a swashplate mechanism used in helicopters to translate the input of helicopter flight control into the motion of the rotor blades, and hence controls the orientation of the rotor blades. In this model, the rotor blades are modeled as either rigid ... 詳細を見る
Thermal Actuator Surrogate Model Application
The Thermal Actuator Surrogate Model application demonstrates how to accelerate computation for multiphysics analysis using a surrogate model. A surrogate model is a simpler, usually computationally cheaper model, which is used to approximate the behavior of a more complex, and often ... 詳細を見る
Bending of a Simply Supported Composite Laminate
This example demonstrates the bending analysis of a simply supported composite laminate under sinusoidal distributed transverse load. The composite laminate is thick, with a thickness to side length ratio of 1/4. The laminate has three layers in a cross-ply layup. The model is solved ... 詳細を見る
High-Cycle Fatigue of a Reciprocating Piston Engine
In a reciprocating piston engine the connecting rods transfer rotating motion into reciprocating motion. The connecting rods are constantly under high stresses and the load increases with the engine speed. A failure of one part in the engine usually results in a replacement of the whole ... 詳細を見る
Lumped Loudspeaker Driver Using a Lumped Mechanical System
Example of a moving-coil loudspeaker where lumped parameters represent the behavior of the electrical and mechanical components. The Thiele-Small parameters (small-signal parameters) serve as input to the lumped model, which is represented using the Electric Circuit interface. The ... 詳細を見る
Water and Carbon Dioxide Co-Electrolysis in a Solid Oxide Electrolyzer Cell
This example models co-electrolysis of H2O and CO2 using a solid oxide electrolyzer cell. The model includes the full coupling between the mass balances and gas flow in the H2 and O2 gas diffusion electrodes, the momentum balances in the H2 and O2 gas flow channels, the energy balance ... 詳細を見る
Impedance Tube Parameter Estimation with Data Generation
Impedance tubes are used for estimating the surface impedance of various samples, for example, a layer of porous material used for sound insulation. This model shows how the five material parameters of the Johnson-Champoux-Allard model can be estimated from the pressure at two ... 詳細を見る
Magnetic–Structure Interaction in a Permanent Magnet Motor
In this example, the coupling between Multibody Dynamics and Rotating Machinery, Magnetic for performing electromagnetic and mechanical analysis is demonstrated. A permanent magnet motor with 10 rotor poles and 12 stator slots is modelled in 2D. The magnets are attached to the ... 詳細を見る