研究開発におけるマルチフィジックスシミュレーションの具体例
さまざまな業界のエンジニア, 研究者, 科学者がマルチフィジックスシミュレーションを使用して革新的な製品の設計とプロセスを研究および開発しています. COMSOL カンファレンスで発表したテクニカルペーパーやプレゼンテーションからインスピレーションを得てください. 以下の選択項目を参照するか, クイック検索ツールを使用して特定のプレゼンテーションを検索するか, アプリケーション領域でフィルタリングします.
COMSOL コンファレンス 2020 論文集を見る
Calculations of the FMR Spectrum in 1D Magnonic Crystals
FMR spectra of the periodic microstructures (one-dimensional magnonic crystals, 1D MCs) were obtained using COMSOL with use partial differential equation interface. Results of these calculations were successfully compared with an experimental data for Damon-Eshbach (DE) and Backward ... 詳細を見る
Geometric Optimization of Piezoelectric Energy Harvesting System
The aim of this paper is to study the effect of geometrical optimization of an array configuration for a unimorph piezoelectric cantilever element. The process involves connecting a previously optimized unimorph piezoelectric cantilever in a two-element array, then in a three-element ... 詳細を見る
A Simplified Numerical Model for Simulating Sliding Door and Surgical Staff Movement in an Operating Theater
This paper deals with a numerical investigation on sliding door and people moving effects on the indoor climate of a standard ISO5 class OT with an ultraclean air filter system and a total ceiling unidirectional diffuser. A simple method to analyze the effects on the OT climate by ... 詳細を見る
Assessing the Potential of Ventilated Facades on Reducing a Buildings’ Thermal Load Using Decoupled COMSOL Simulations
Solar radiation is a prominent contributor of energy in buildings, and can be transmitted directly into a building through opaque surfaces, but it can also be absorbed by building components (i.e. walls, roofs etc.). This study discusses the use and effect of ventilated facades, with an ... 詳細を見る
Thermo-Fluid Dynamics FEM Simulation of Advanced Water Cold Plates for Power Electronics
Introduction: Power electronic converters such as those for High Energy Physics Experiments (HEPEs) must operate in thermally hostile environment. Heat generated by electronics components must be conveniently dissipated to ensure electrical performances and improve reliability. Due to ... 詳細を見る
3D Modeling of Urban Areas for Built Environment Applications Using COMSOL
This paper presents the modeling and simulation results of wind velocities in urban areas. The main idea was to build random generated urban areas for studying the influence of different urban geometries, from relative open to more dense, on wind profiles. The Spalert-Allmaras turbulent ... 詳細を見る
Multiphysics Modeling of Swelling Gels
Polymer gels belong to the realm of soft active materials as they are capable of responding to a non-mechanical stimulus – the permeation of a solvent – with a mechanical action – a volume change, thanks to the coupling between different physics. This mechanism of coupling can be ... 詳細を見る
Simulation and Design of a Microfluidic Respirometer for Semi-Continuous Amperometric Short Time Biochemical Oxygen Demand (BODST) Analysis
Introduction: This work presents the design of a novel flow cell based miniaturized electrochemical respirometer to monitor organic content in water samples semi-continuously, in contrast to current Biochemical Oxygen Demand, BOD, methods. Simulation techniques has been used to ... 詳細を見る
Application of the Hot Wire Technique and COMSOL Multiphysics for Heat Transfer Monitoring in Solids
We applied the Hot Wire (HW) technique and COMSOL Multiphysics software to study the heat transfer of a homogeneous and isotropic solid material. The HW technique is based on the application of a linear power density modulated by a rectangular pulse of heat, in a specific time period. ... 詳細を見る
Modeling the Chemical Decomposition of Sodium Carbonate Peroxyhydrate
The challenge with the use of Sodium Carbonate Peroxyhydrate (Na2CO3*1.5H2O2) as a bleach source in dry detergent formulations is its lower stability in comparison with other materials, and the risk of quality losses of the product over the shelf life. The issue can be solved with the ... 詳細を見る