研究開発におけるマルチフィジックスシミュレーションの具体例
さまざまな業界のエンジニア, 研究者, 科学者がマルチフィジックスシミュレーションを使用して革新的な製品の設計とプロセスを研究および開発しています. COMSOL カンファレンスで発表したテクニカルペーパーやプレゼンテーションからインスピレーションを得てください. 以下の選択項目を参照するか, クイック検索ツールを使用して特定のプレゼンテーションを検索するか, アプリケーション領域でフィルタリングします.
COMSOL コンファレンス 2020 論文集を見る
Asymmetry Induced Terminal Voltage Improvement in Mg2Si-based Thermoelectric Unicouple
Thermoelectric power generation has been envisioned as a clean energy alternative to conventional thermal to electric power generation for decades due to its noiseless and low-cost operation. However, a typical thermoelectric generator suffers from low device efficiency, so it has been a ... 詳細を見る
Numerical Study of Laminar Forced Convection Cooling of Circuit Board Mounted Heat Source Array
This paper deals with the numerical study of optimal distribution of rectangular heat sources populated on a substrate board for electronic cooling. The simulations are performed for laminar forced convection conjugate heat transfer with vertical orientation of substrate board. The ... 詳細を見る
Experimental Validation of Induction Heating of MS Tube for Elevated Temperature NDT Application
Induction heating is multiphysics process, which includes electromagnetic induction and heat transfer. Both the physics are nonlinearly coupled with each other. In this paper, mathematical modeling of induction heating of MS tube for elevated temperature NDT application is presented. ... 詳細を見る
Thermal Modeling of Chlorination Reactor
Chlorine reactor is used to dry molten LiCl-KCl eutectic salt before it is put to use in electrorefining operation. Molten salt electrorefining is a pyrochemical method of separation of heavy elements from spent metallic nuclear fuel. It is a high-temperature process which uses molten ... 詳細を見る
Modeling of Residual Stresses in a Butt-welded Joint with Experimental Validation
2D-modeling of arc welding in butt-joint configuration was performed in this study considering thermal-structural interactions. Thermal behavior was modeled in COMSOL Multiphysics® using the Heat Transfer Module with weld heat input as a Gaussian pulse whereas structural behavior using ... 詳細を見る
A Study on Hydrodynamics of Melt Expulsion in Pulsed Nd: YAG Laser Drilling of Titanium
Laser drilling of titanium and its alloys is widely used in aerospace industry, as it offers selective removal of material at high accuracy and speed. However, laser drilling often inherits defects such as large heat affected zone, micro cracks and recast layer. These defects depend upon ... 詳細を見る
MEMS based Gecko Foot for Micro Robotics
Gecko foots have inspired researchers to develop designs that can help robots to tread vertically oriented surface. These nanobots find many applications as they can perform a lot of operations more efficiently and also lower the cost of such operations. These can be employed in various ... 詳細を見る
Thermal Modelling of Lunar Surface at Regional Scales using COMSOL Multiphysics®
The thermal behavior/heat flow of the Moon provides us an insight into its geophysical character and thermal evolution. The thermal behavior within the uppermost (top few meters) regolith layers is more complex due to their complex geometric, thermal and radiative properties. In order to ... 詳細を見る
Modeling of Humidification using COMSOL Multiphysics®
In the following study COMSOL Multiphysics® was used to simulate evaporation of water droplets in a stream of heated air. This was a precursor to the modeling of a humidifier, which is used to humidify the air supplied to fuel cell stack. Since the percentage of water droplets was ... 詳細を見る
Pre-clinical Modelling and Simulation of Hepatic Radiofrequency Ablation
Radio-Frequency ablation (RFA) has received a considerable interest as a minimally invasive treatment technique used for destruction of a variety of primary and metastatic hepatic tumors. A parametric study of hepatic radio-frequency ablation using three-dimensional numerical models has ... 詳細を見る