アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL Access アカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
Droplet evaporation is ubiquitous in everyday life and is essential in many industrial processes, such as inkjet printing, cleaning/coating of surfaces, and phase change heat transfer. This model demonstrates how to model phase transition by a moving exterior boundary condition using ... 詳細を見る
A magnet moving axially through the center of a coil will induce a voltage across the coil terminals. One practical application of this is in shaker flashlights, where the flashlight is vigorously shaken back and forth, causing a magnet to move through a multi-turn coil, which provides ... 詳細を見る
このモデルは, 互いに等距離に配置された GaAs 柱で構成されるフォトニック結晶における波動伝播を調査します. 柱間の距離は, 光の波数と周波数の関係を決定し, 特定の波長の光が結晶構造内を伝播するのを防ぎます. この周波数範囲はフォトニックバンドギャップと呼ばれます. 特定の構造には複数のバンドギャップがあり, このモデルは結晶の最低周波数帯域のバンドギャップを抽出します. バンドギャップ解析には, 主に2つの複雑な問題があります. 1つは, GaAs の屈折率が周波数に依存することです. 2つ目は, ... 詳細を見る
The mutual inductance and induced currents between a single turn primary and twenty turn secondary coil in a concentric coplanar arrangement is computed using a frequency domain model. The secondary coil is modeled using a homogenized approach which does not explicitly consider each turn ... 詳細を見る
This is a model of the Brüel and Kjær 4134 (BK 4134) condenser microphone. The geometry and material parameters are those of the actual microphone. The modeled sensitivity level is compared to measurements performed on an actual microphone and shows good agreement. The membrane ... 詳細を見る
This is a 2D model of an anisotropic porous absorbing material. The absorption coefficient alpha are determined as functions of frequency for three different incidence angles. The example uses Periodic Floquet boundary conditions. The model uses two different methods for modeling the ... 詳細を見る
シェル ‐ チューブ熱交換器は, 石油精製所やその他の大規模な化学プロセスでよく使用されます. このモデルでは, 異なる温度の2つの分離された流体が熱交換器を流れ, 1つはチューブ (チューブ側) を, もう1つはチューブの周りのシェル (シェル側) を流れます. シェル ‐ チューブ熱交換器の最適なパフォーマンスは, いくつかの設計パラメーターと動作条件によって左右されます. このモデルは, 熱交換器モデルを設定するための基本原則を示しています. これは, パラメータースタディや, 腐食, 熱応力, 振動などの追加効果を伴う, ... 詳細を見る
Hydrodynamic bearings generate heat due to the viscous losses in the lubricant. As a result, the temperature of the rotor increases causing deformation and thermal stresses in both the rotor and the bearing housing. This example shows how to model different physical phenomena that are ... 詳細を見る
This example solves for the temperature distribution inside a vacuum flask holding hot coffee. The main purpose is to illustrate how to use MATLAB functions to define material properties and boundary conditions. 詳細を見る
Drying of porous media is an important process in the food and paper industry among others. Many physical effects must be considered: fluid flow, heat transfer with phase change, and transport of participating liquids and gases. All of these effects are strongly coupled, and predefined ... 詳細を見る
