アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL アクセスアカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
This example replicates the results of the Jelly Roll tutorial example using a flattened representation of the wound spiral-based geometry. See that model entry for details on the background, original geometry, materials, and the general physics setup. Mapping the original problem to a ... 詳細を見る
This model demonstrates the analysis of lightning surges on high voltage transmission line towers. Lightning carrying a current of 10 kA struck one of the tower's shielded wires. The induced voltage at the three-phase conductors are computed. Some highlights of this model: Perform ... 詳細を見る
The fluid flow in seals causes a strong restoring radial force, opposing the shaft motion. Also, there is a cross coupled force due to the axial variation of the circumferential flow. The first type of force always has a stabilizing effect on the rotor, whereas the second one in certain ... 詳細を見る
This model computes the transmission probability through an RF coupler using both the angular coefficient method available in the Free Molecular Flow interface and a Monte Carlo method using the Mathematical Particle Tracing interface. The computed transmission probability determined by ... 詳細を見る
斜角超音波ユニットは, 金属パイプなどの固体の非破壊検査 (NDT) に使用されます. これらは, 気孔, 小さな亀裂, 融合不足など, 溶接領域内および溶接領域周辺の欠陥を検出するのに特に役立ちます. 斜角 NDT は, 垂直ビーム検査では欠陥を見つけるのが難しい場合によく使用されます. たとえば, 亀裂が垂直で細いため, 反射量が少ないために検出できない場合などです. 斜角 NDT の動作原理は, トランスデューサーによって送信された縦波 (圧縮波) をテストサンプルで屈折した横波 (横波) に変換することにあります. 次に, ... 詳細を見る
Continuous mixing is used in process equipment to mix components in a single pass. Compared to batch mixing, this operation has the advantage that the tank filling and emptying steps are eliminated, implying that the process can be run without interruptions. A disadvantage of continuous ... 詳細を見る
Predicting the noise radiation from a dynamic system gives designers insight into the behavior of moving mechanisms early in the design process. For example, consider a gearbox in which the change in the gear mesh stiffness causes vibrations. These vibrations are transmitted to the ... 詳細を見る
This tutorial model is of a micro perforated plate (also known as MPP) backed by a vibrating structure. This is a typical configuration in, for example, a MEMS microphone. The vibrating structure is not modeled explicitly, but just assigned a vibration velocity. The vibrating structure ... 詳細を見る
潜水艦の主な防御力は, 作戦中に潜水艦を隠蔽し続ける能力にあります. 電波は海水に強く吸収されるため, 音響航法測距 (ソナー) は潜水艦探知に用いられる主要な方法の一つです. ソナーシステムは, 水中探査や漁業にも用いられています. 設計者は, 潜水艦の等価反射面積を最小化するために, 音波の反射方法を解析します. ターゲット強度 (TS) は, ソナーターゲットの面積を表す指標です. このチュートリアルでは, ベンチマークターゲットエコー強度シミュレーション (BeTTSi) を用いたベンチマーク潜水艦のTSを解析するための簡略化された手法を紹介します. ... 詳細を見る
The topology optimized Tesla microvalve is used as inspiration for a parametrized geometry. The optimization of this geometry takes erosion and dilation of the geometry into account by optimizing over a parametric sweep. In this example the optimization is driven by the worst of the 3 ... 詳細を見る