アプリケーションギャラリ

Predicting the noise radiation from a dynamic system gives designers insight into the behavior of moving mechanisms early in the design process. For example, consider a gearbox in which the change in the gear mesh stiffness causes vibrations. These vibrations are transmitted to the ... 詳細を見る

Galvanic corrosion between two different phases (alpha and beta phases) in a metallic (magnesium) alloy is simulated for a representative cross-sectional microstructure configuration. A key feature in the model formulation is the implementation of both anodic and cathodic regions at ... 詳細を見る

リチウムイオン電池の負極グラファイト電極上の銅コレクターは, 過放電時に溶解することが確認されています. 溶解により集電体が不可逆的に損傷し, 溶解した銅イオンが再析出してデンドライトを形成する可能性があるため, 安全上の懸念事項となります. 電池は通常, 過放電を回避するために, セルレベルまたはパックレベルのいずれかで指定された電圧制限内で動作します. しかし, パック内では個々のセル間の電荷不均衡により, あるいはこのチュートリアルで部分的に調査するように, 単一の電池セル内の電極の局所的な不均一性により, 過放電が発生する可能性があります. ... 詳細を見る

This example calculates the spectral properties of a 3D optical ring resonator. The model demonstrates how to use parts from the Wave Optics Parts Library and how to setup the Field Continuity boundary condition at boundaries, where there is a jump in the predefined phase approximation. 詳細を見る

アルカリ水電解は, 水素ガスを生成するための確立された工業プロセスです. セル内では, 陰極で水素ガスが, 陽極で酸素ガスが生成されます. 電解液は水溶液であり, 発生したガスが泡状になると, 実効イオン伝導率が低下します. また, 発生したガスは, 電極反応がアクセス可能な表面積を減少させることから, セルの性能に悪影響を及ぼす可能性があります. この例では, ガス生成がアルカリ電解セルの性能に与える影響を調査します. 詳細を見る

This model simulates the discharge of a Nickel-Metal Hydride (NiMH) battery using the Battery with Binary Electrolyte interface. The geometry is in one dimension and the model is isothermal. The model serves as an introduction to NiMH modeling, and can be further extended to include ... 詳細を見る

Some positive electrode materials are known to deteriorate in overcharged lithium-ion battery cells. Predominantly, manganese containing electrode materials such as LMO and NMC can loose capacity due to manganese dissolving from the materials at overcharge. This decomposition is a ... 詳細を見る

A Fabry-Perot resonator is one of the fundamental optical devices and has a broad range of applications. A few examples are that it can be used to measure length, frequency/wavelength or to filter specific spatial modes. This model uses the Beam Envelopes Interface in the bidirectional ... 詳細を見る

For an electrochemical reaction to occur, the reacting species usually needs to adsorb to the electrode surface before undergoing reduction or oxidation, after which the resulting product species desorbs back into the electrolyte. If the rate of adsorption or desorption is slow in ... 詳細を見る

This example models co-electrolysis of H2O and CO2 using a solid oxide electrolyzer cell. The model includes the full coupling between the mass balances and gas flow in the H2 and O2 gas diffusion electrodes, the momentum balances in the H2 and O2 gas flow channels, the energy balance ... 詳細を見る