アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL アクセスアカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
この例では, 4C 放電中のバッテリパック内の温度分布をモデル化する方法を示します. パックは, まず2つの円筒電池を並列に接続して構成されます. 次に, 並列接続された6つのペアを直列に接続して, 完全なパックを作成します. (これは 6s2p 構成とも呼ばれます. ) 問題の対称性は 2回使用されるため, 3つの電池の温度分布のみを解けば済みます. 適切な熱源を生成するために, 集中電池インターフェースの3つのインスタンスが使用され, その後, 3Dジオメトリ内の1つの伝熱インターフェースに結合されます. 詳細を見る
This model treats the free convection and heat transfer of a glass of cold water heated to room temperature. Initially, the glass and the water are at 5 °C and are then put on a table in a room at 25 °C. The nonisothermal flow is coupled to heat transfer using the Heat Transfer module. 詳細を見る
The layout of a district heating network is designed using topology optimization. 詳細を見る
In this model, a rotor with permanent magnets and a nonlinear magnetic material rotates within a stator of the same magnetic material. The generated voltage in windings around the stator is calculated as a function of time. COMSOL Multiphysics models the rotation with assemblies and ... 詳細を見る
シェル ‐ チューブ熱交換器は, 石油精製所やその他の大規模な化学プロセスでよく使用されます. このモデルでは, 異なる温度の2つの分離された流体が熱交換器を流れ, 1つはチューブ (チューブ側) を, もう1つはチューブの周りのシェル (シェル側) を流れます. シェル ‐ チューブ熱交換器の最適なパフォーマンスは, いくつかの設計パラメーターと動作条件によって左右されます. このモデルは, 熱交換器モデルを設定するための基本原則を示しています. これは, パラメータースタディや, 腐食, 熱応力, 振動などの追加効果を伴う, ... 詳細を見る
This application illustrates how to model an electric machine, such as a generator, motor, or drive, by exploiting its sector symmetry to reduce the size of the problem. The machine being studied is a simplified electric generator in 3D, based on the geometry used in the generator_2d ... 詳細を見る
This classical verification model solves the steady state temperature distribution in a plan disk heated by a localized heat source at its center. It shows and compare different ways to define a heat source localized on a small domain by representing it either as a geometrical point or a ... 詳細を見る
This tutorial shows how to set up a 3D simulation of rubber injection molding. A phase field method is used to track the interface between the rubber and the displaced air. The rubber is modeled as shear-thinning inelastic non-Newtonian power law fluid with a fluid-consistency ... 詳細を見る
This model demonstrates how to simulate a metasurface beam deflector that uses anomalous refraction. The structure itself is a repeated array of six posts (so-called meta elements). The periodicity of the individual posts is 500 nm, so the full structure of six posts is 3 um wide. The ... 詳細を見る
Microwave filters are used to eliminate unwanted frequency components in the output from microwave transmitters. They are typically inserted between a power amplifier and an antenna. The amplifiers are nonlinear and produce harmonics that must be eliminated with filters that have a ... 詳細を見る