技術情報とプレゼンテーション

クイック検索

資力

ホワイトペーパーとアプリケーションノート

研究開発におけるマルチフィジックスシミュレーションの具体例

さまざまな業界のエンジニア, 研究者, 科学者がマルチフィジックスシミュレーションを使用して革新的な製品の設計とプロセスを研究および開発しています. COMSOL カンファレンスで発表したテクニカルペーパーやプレゼンテーションからインスピレーションを得てください. 以下の選択項目を参照するか, クイック検索ツールを使用して特定のプレゼンテーションを検索するか, アプリケーション領域でフィルタリングします.

COMSOL コンファレンス 2020 論文集を見る

すべて

Bengaluru 2023

ヨーロッパ 2020

Computational Fluid Dynamicsx

Heat Transfer Modeling of Steam Methane Reforming

E. Carcadea[1], M. Varlam[1], I. Stefanescu[1]
[1]National Research Institute for Isotopic & Cryogenic Technologies, Rm.Vâlcea, Romania

Steam methane reforming is a widely studied process because of its importance for hydrogen production. A two-dimensional membrane-reactor model was developed to investigate the steam-methane reforming reactions. The use of membrane as membrane-reactor separator offer us few advantages ... 詳細を見る

A Coulomb Stress Model to Simulate Induced Seismicity Due to Fluid Injection and Withdrawal in Deep Boreholes

G. Perillo[1], G. De Natale[2], C. Troise[2], A. Troiano[2], M.G. Di Giuseppe[2], A. Tramelli[2]
[1]University of Naples Parthenope, Naples, Italy
[2]INGV, Osservatorio Vesuviano, Naples, Italy

Fluid injection and withdrawal in deep wells is a basic procedure in mining activities and deep resources exploitation, i.e. oil and gas extraction, geothermal exploitation, geothermal permeability enhancement and waste ?uid disposal. All these activities have the potential to induce ... 詳細を見る

Multiphysics Simulations of Granular Sludge on the Optimization of Effluent Treatment Plant

S. Gunsekaran [1], R. C. Thiagarajan[1]
[1]ATOA Scientific Technologies Private Limited, Bangalore, India

Multiphysics Simulations of Physico-chemical and Biological Treatment of wastewater is increasing due to the demand for cost efficient plant design and utilization. Among the many processes, a thorough understanding of the settling behavior of an activated granular sludge in the ... 詳細を見る

Low Pt Cathodes for High Performance PEMFCs: Modeling and Experiments

F. Daouda[1], J. Hamelin[1], P. Benard[1], S. Kumar Natarajan [1]
[1]Insitut de recherche sur l'hydrogène, Université du Québec à Trois-Rivières, Trois-Rivières, Québec, Canada

We present a novel multi-layered electrode fabrication technique for polymer electrolyte membrane fuel cells (PEMFCs). This method consists of alternate layers of Pt deposition (0.05 mg/cm²) by sputtering on the painted multi-walled carbon-Nafion layer (CNL) with larger concentration of ... 詳細を見る

Multiphysics Simulation of a Circular-Planar Anode-Supported Solid Oxide Fuel Cell

K. Daneshvar[1], A. Fantino[1], C. Cristiani[1], G. Dotelli[1], R. Pelosato[1], M. Santarelli[2]
[1]Politecnico di Milano, Dipartimento di Chimica, Materiali e Ingegneria Chimica “G. Natta”, Milano, Italy
[2]Politecnico di Torino, Dipartimento di Energetica, Torino, Italy

A 2D isothermal axisymmetric model of an anode-supported Solid Oxide Fuel Cell (SOFC) has been developed. Also a parametric analysis to find the effect of important parameters on the cell performance has been done. This simulation has been carried out at 1 atm and 1073 K. The PEN ... 詳細を見る

Geometric Modeling and Numerical Simulation of Airfoil Shapes Using Integrated MATLAB® and COMSOL Multiphysics

A. Safari[1], H. Lemu G.[1], H. Severson[1]
[1]University of Stavanger, Stavanger, Norway

This paper proposes a framework for an efficient integration between geometric modeling program and analysis tool for a coming automated aerodynamic design optimization mission. This demand can be addressed by using both in-house codes and commercial software which have the good ability ... 詳細を見る

Comparative Numerical Studies of Scramjet Inlet Performance Using k-? Turbulence Model with Adaptive Grids

V. Gopal[1], R. Kolluru[1]
[1]BMS College of Engineering, Bangalore, Karnataka, India

Scramjet inlet design remains as a key aspect for hypersonic flight. To assess the inlet design, the performance parameters namely; air-capture ratio, total pressure efficiency, inlet drag coefficient, and kinetic energy efficiency are evaluated and analysed. In the current study ... 詳細を見る

Calibration of MHD Flow Meter using COMSOL Multiphysics

S. Sahu[1], R. P .Bhattachryay[1], E. R. Kumar[1]
[1]Institute for Plasma Research, Bhat, Gandhinagar, Gujarat, India.

There is limited option for non-intrusive flow measurement of liquid metals at high temperature. Liquid metal flowing in a conduit along with the transverse magnetic field induces emf in the liquid metal. The emf developed; which has linear dependency on flow velocity; can be used for ... 詳細を見る

Design and Simulation of Piezoelectric Micropump and Microvalve based Drug Delivery System

D. Samajdar[1], P. Podder[1], A. Bhattacharyya[1], S. Sen[1]
[1]Institute of Radio Physics and Electronics, University of Calcutta, Kolkata, WB, India

In the emerging field of MEMS microfluidics, micropumps and microvalves are two of the most important devices with a wide spectrum of applications such as programmable drug delivery systems, lab-on-a chip devices, µTAS (micro total analysis system), micro electric cooling applications ... 詳細を見る

Modelling and Simulation of Single Phase Fluid Flow and Heat Transfer in Packed Beds using COMSOL Multiphysics

S. Sachdev[1], S. Pareek[1], B. Mahadevan[1], A. Deshpande[1]
[1]Department of Chemical Engineering, BITS Pilani Goa Campus, Zuarinagar, Goa, India

Computational fluid dynamics has emerged as an advanced tool for studying detailed behavior of fluid flow and heat transfer characteristics in many chemical engineering applications like packed beds. Packed beds play an important role in various chemical industries. Hence understanding ... 詳細を見る

最初

前

711–720 of 1092

次

最後