Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Numerical Modeling of Sampling Airborne Radioactive Particles Methods from the Stacks of Nuclear Facilities in Compliance with ISO 2889 - new

P. Geraldini[1]
[1]Sogin Spa, Rome, Italy

The main objective of this study is to verify the compliance of an ongoing nuclear facilities stack design with the ISO 2889 requirements, during normal and off-normal conditions. In particular, with the numerical simulations, they have been identify well-mixed sample locations along the chimney and the compliance with the International Standard requirements as result of stack flow rate and ...

Heat Conduction in Porous Absorption Layers for Thermography Applications - new

L. Helmich[1], A. Huetten[1]
[1]Bielefeld University, Bielefeld, Germany

Thermography measurements on metallic thin films are challenging due to reflections from the environment. We present a thin "gold black" absorption layer to deal with this issue. A multiphysics model is introduced to correct the experimentally obtained data for undesirable heat transfer effects between the metallic sample and the absoption layer.

Simulation and Experimental Characterizations of a Thin Touch Mode Capacitive Pressure Sensor

A.-M. El Guamra [1], D. Bühlmann [1], F. Moreillon [1], L. Vansteenkiste [1], P. Büchler [2], A. Stahel [3], P. Passeraub [1],
[1] HES-SO University of Applied Sciences Western Switzerland, Delémont, Switzerland
[2] Institute for Surgical Technology & Biomechanics, University of Bern, Bern, Switzerland
[3] Bern University of Applied Sciences Engineering and Information Technology, Bern, Switzerland

Introduction: This study describes a thin and low-cost capacitive pressure sensor in touch mode (TM) for monitoring fluid pressure from 0 to 40kPa in fluidic chambers with Luer fittings for medical applications. TM provides good linearity, large measuring range and large overload protection [1]. The choice of a thin polymer membrane as sensitive element with printed circular electrodes reduces ...

Asymmetry Induced Terminal Voltage Improvement in Mg2Si-based Thermoelectric Unicouple

P. Priyadarshi [1], J. Bahl [1], B. Muralidharan [1]
[1] Indian Institute of Technology Bombay, Mumbai, India

Thermoelectric power generation has been envisioned as a clean energy alternative to conventional thermal to electric power generation for decades due to its noiseless and low-cost operation. However, a typical thermoelectric generator suffers from low device efficiency, so it has been a constant endeavor for thermoelectric researchers’ community to consider alternate thermoelectric materials ...

Application of Kelvin's Inversion Theorem to the Solution of Laplace's Equation Over a Domain That Includes the Unbounded Exterior of a Sphere

J. Russell[1]
[1]Florida Institute of Technology, Melbourne, FL, USA

In simulating physical systems modeled as solutions of partial differential equations over an unbounded domain, a challenge arises owing to the impossibility to cover an unbounded domain with a mesh. A classical problem in fluid dynamics, a solid sphere of radius a_s is submerged in a tank of water (at rest) of much larger size. The water is disturbed by the sphere’s sudden acceleration in the z ...

Frequency Analysis of Si-Wafers with Variable Size and Boundary Conditions

E. Gehrig [1],
[1] Hochschule RheinMain, University of Applied Sciences, Wiesbaden Rüsselsheim, Wiesbaden, Germany

Silicon wafers represent key elements in modern microelectronics or photovoltaics. Technological fabrications of wafer sizes with large diameters (e.g. 450 mm) allow an efficient realization for integrated circuits at low cost. However, this material shows a high sensitivity to vibrations that strongly depends on size and the positioning as well as orientation of a wafer in a mounting, realized ...

Modeling and Simulation of Piezoresistive Pressure Sensor for 2bar Application

M. Ramezani [1], M. El Barkouky [1],
[1] Melexis, Tessenderlo, Belgium

In this paper, we focused on modeling of the piezoresistive pressure sensors. The Structural Mechanics Module of COMSOL Multiphysics® software is used to model the sensor and make a comparative study of the MEMS pressure sensor with different shape and size of membrane. The impact of membrane shape and size on sensitivity and nonlinearity of the pressure sensor is investigated. For example, it ...

Multiphysics Simulation of a Self-heating Paraffin Membrane Microactuator

P. Lazarou[1], C. Rotinat[1]
[1]CEA LIST/DIASI/LRI, Paris, France

A grand variety of microactuator technologies and demonstrators has been introduced during the last years. Of particular interest are the microactuators based on phase change materials and especially paraffin wax, which can volumetrically expand up to 15%, providing high force actuation. The object of this study is the numerical validation of a paraffin microactuator concept by coupling multiple ...

Voltage and Capacitance analysis of EWOD system using COMSOL

D. Das[1], S. Sohail[1], S. Das[2], and K. Biswas[1]
[1]Electrical Engineering Department, IIT Kharagpur, India
[2]School of Medical Science and Technology, IIT Kharagpur, India

Electrowetting on Dielectrics (EWOD)systems is widely practiced digital microfluidic technique, used in Lab-on-a-Chip (LoC) system for biomedical application. In EWOD, with applied potential, the droplet minimizes its surface energy by transiting towards the actuated electrode. The problems with EWOD device for biological sample are that it will damage the cells if applied voltage across it ...

Modeling of Straight Jet Dynamics in Electrospinning Process

R. Pandya [1], A. Kumar [2], V. Runkana [1],
[1] Tata Research Development and Design Centre, Tata Consultancy Services, Pune, India
[2] Indian Institute of Technology, Delhi, India

Electrospinning is a process where high voltage is applied to produce polymer fibers of nanoscale diameter. Various polymers have been used for this process in molten form or as a solution with an appropriate solvent such as glycerol. The melt solidifies while the solvent evaporates to produce fibers. The fibers produced have properties such as high surface to volume ratio and a molecular ...