アプリケーションギャラリ

この非従来型の多孔質媒体流れモデルは, 多孔質媒体の隙間におけるクリープ (ストークス) 流を利用します. このモデルは, カリフォルニア大学サンタバーバラ校の Arturo Keller 氏, Maria Auset 氏, Sanya Sirivithayapakorn 氏が行った細孔スケールの流れ実験に基づいています. モデルに使用されている形状は, 走査型電子顕微鏡画像から作成されました. この例では, Keller 氏, Auset 氏, Sirivithayapakorn 氏による 2D マイクロ媒体画像の1つを使用し, ... 詳細を見る

This model describes a static stress analysis to obtain the stress distribution in the vicinity of a small hole in an infinite plate. The model is a classic benchmark and is described in Mechanics of Material, by D. Roylance. The stress level is then compared with the theoretical values. 詳細を見る

This is a benchmark model involving stick-slip friction of a ring rolling inside another ring. The displacement of the inner ring is computed and compared to the analytical result. This model also shows how to tackle friction dominated contact problem. 詳細を見る

This tutorial shows how to evaluate the harmonic response of a structure with a moderately nonlinear behavior. A nonlinear problem can only be solved using time-domain analysis. A way to speed up the computation is to use a linearized frequency response analysis to provide good initial ... 詳細を見る

A fuel cell stack operates at temperatures just below 100 °C, which means that it has to be heated at start-up. The fuel cell stack consists of unit cell of anode, membrane, and cathode connected in series through bipolar plates. This study presents a model that couples the thermal and ... 詳細を見る

A circular metal bar is subjected to uniaxial tension. As an effect, large plastic strains develop. The material is elastoplastic with nonlinear isotropic hardening. As the elongation is increased, the decrease in radius becomes strongly nonuniform, so called "necking". The development ... 詳細を見る

This is a benchmark model for flexible multibody dynamics. This model simulates the dynamic behavior of a planar four-bar mechanism when one of the joints has a defect. The out-of-plane motion in the mechanism, caused by the defect in the joint, is compared with the results from the ... 詳細を見る

この例では, 容器内に沈められた加熱チューブの配列と, その底部から流体が流入する様子について説明します. これは, 熱伝達と結合した流体力学を含むため, マルチフィジックスモデルです. 圧力と速度場はナビエ・ストークス方程式の解であり, 温度は熱方程式を通じて解かれます. このモデルでは, 方程式は両方向に結合されています. 流体を持ち上げる浮力は, 密度を通じて温度に依存する力項を介して圧縮性ナビエ・ストークス方程式に入力されます. 同時に, 熱方程式は対流熱伝達を考慮します. この実装では, ... 詳細を見る

Different types of elements can be used for modeling a rotor, depending on the level of complexity and the type of the system being modeled. The modeling steps and representation of the results will vary with the type of idealization. In this tutorial model, an eigenfrequency analysis is ... 詳細を見る

This model uses the Optimization interface to solve the inverse problem for determining the spatially variable hydraulic conductivity on a discretized quadratic grid from a number of aquifer pump tests. Because the number of observations is smaller than the number of unknown parameters, ... 詳細を見る