アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL Access アカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
An evanescent mode cavity filter can be realized by adding a structure inside of the cavity. This structure changes the resonant frequency lower than the dominant mode of the unfilled cavity. A piezo actuator is used to control the size of a small air gap which provides the tunability of ... 詳細を見る
A standing contact fatigue test is a procedure used for testing crack growth on the subsurface level. In such a test, a spherical object is pressed against the tested materials and cycled between a high and low compressive load. No translational movement between the two occurs. After a ... 詳細を見る
Classical MHD benchmark problem was solved analytically by J. Hartmann. He considered laminar incompressible flow between two planes (in planar duct) in transversal imposed magnetic field under next assumptions: * fully developed flow (far from inlet) * fluid properties are constant * ... 詳細を見る
This models pressure-dependent heating of 4 inch wafer on unipolar electrostatic chuck. Wafer sits on top of ring with electrostatic force holdong down wafer to counter upward pressure from gas flowing in gap between wafer and chuck surface. It is a problem involving 4 coupled physics ... 詳細を見る
This example shows how to use the Optimization Module to find a coil geometry giving a uniform magnetic field on axis and minimal field near the axis ends. 詳細を見る
この例では, 油水懸濁液がオリフィスを通過する乱流流れを考慮します. 懸濁液がオリフィスを通過する際, 油滴は乱流応力によって小さな液滴に分割されます. このモデルの目的は, 液滴サイズの分布を追跡することです. 液滴サイズ分布は, 直径の異なる5つの液滴集団に離散化されます. このモデルは, 相輸送混合モデル, 乱流, k-ε マルチフィジックスインターフェースを用いて, 混合物の流れ場と, 異なる液滴集団の輸送を計算します. 詳細を見る
ガイド波に属するラム波の数値モデル化は, 長距離超音波検査用の構造ヘルスモニタリング (SHM) システムの分析と設計に不可欠です. ガイド波に基づく SHM システムの設計は, 2つの主要な部分で構成されます. まず, 特定の断面の導波管で伝搬できるモードの分散曲線を知る必要があります. 次に, 選択したモードの導波管を通じた伝搬と, 断面積の可能性のある不規則性 (破損または腐食欠陥) からの反射を時間領域で分析します. このチュートリアルでは, 有限の幅と厚さを持つ鋼板における誘導波の伝播について学習します. ... 詳細を見る
One method of creating spring-like structures or inducing curvature in thin structures is to plate them to substrates that are under the influence of residual stresses. The plating process can control this stress even for similar materials. One such device is the electrostatically ... 詳細を見る
