アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL Access アカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
蓄熱ユニットは, 太陽熱, 地熱, または廃熱源からの熱エネルギーを蓄積するために使用されます. 最もシンプルなユニットは, 家庭でよく見られる水タンクで構成され, 太陽エネルギーを検知可能熱として蓄えます. これらのタンクの熱容量は潜熱を蓄えることでさらに増加し, 潜熱蓄熱 (LHS) ユニットとして利用されます. 通常, LHS タンクには, 相変化物質としてパラフィンが充填された球状カプセルが内蔵されています. この例では, 充填ベッド蓄熱タンク内の流れをモデル化し, 相変化を伴う熱伝達と LHS ユニットへの充填時の局所的な熱非平衡の影響を考慮しています. 詳細を見る
流体ダンパーは, 軍事機器における衝撃吸収, 土木構造物における地震や風による振動の抑制など, 様々な用途に使用されています. 流体ダンパーは, 機械エネルギーを熱に変換することで機能します. このモデルは, 流体ダンパーにおける粘性加熱とそれに伴う温度上昇の現象を示します. 粘性加熱はマイクロ流体デバイスにおいても重要です. マイクロ流体デバイスでは, 断面積が小さく長さが長いため, 大きな発熱が発生し, 結果として流体の流れに影響を与える可能性があります. このモデルでは, 共役熱伝達, 層流, 移動メッシュの各インターフェースを用いて時間依存スタディを実施します. 詳細を見る
A square airbag made of a hyperelastic, compressible neo-Hookean material is inflated using pressurized air. Compressive stresses trigger wrinkling in some regions of the thin airbag. In this example, the wrinkling behavior is modeled using tension field theory, which gives a correct ... 詳細を見る
The mass of an aluminum beam is minimized subject to a displacement constraint and a distributed load. The problem is solved using parameter, shape and topology optimization. 詳細を見る
This is a benchmark model for an axisymmetric transient thermal analysis. The temperature on the boundaries changes from 0 degrees C to 1000 degrees C at the start of the simulation. The temperature at 190 s from the anlysis is compared with a NAFEMS benchmark solution. 詳細を見る
Composite materials are often used in structural applications, where the ability to tailor properties such as stiffness and strength make them attractive compared to traditional engineering materials. In addition to structural applications, composites are also used in applications where ... 詳細を見る
This tutorial demonstrates how a lumped model of a MEMS transducer can be derived from its FEM model. It includes an FEM model of a capacitive micromachined ultrasonic transducer (CMUT) and the corresponding lumped model created using the Lumped Mechanical System (LMS) interface. The ... 詳細を見る
This model describes the evaporation of a droplet that consists of concentrated solution of acetone and water. It accounts for the coupled phenomena of chemical species transport and heat transfer over phase boundaries (liquid-gas boundary) as well as for multiphase flow. The droplet ... 詳細を見る
In this example, the deformation of a rubber boot seal connected to a rigid pipe is studied. As the pipe rotates and the seal deforms, the flanges of the seal self-intersect and it also come into contact with the pipe. 詳細を見る
