M. K. Gobbert, X. Huang, S. Khuvis, S. Askarian, B. E. Peercy
University of Maryland - Baltimore County, Baltimore, MD, USA
This paper presents information on techniques needed in COMSOL Multiphysics® to enable computational studies of coupled systems of PDEs for time-dependent non-linear problems. Furthermore, we demonstrate how to use data files as input for initial conditions. To illustrate the techniques, we consider a system of two time-dependent non-linear PDEs from mathematical biology that couples an ...
A Multiphase Porous Medium Transport Model with Distributed Sublimation Front to Simulate Vacuum Freeze Drying
A. Warning, J. M. R. Arquiza, A. K. Datta
Cornell University, Ithaca, NY, USA
A continuum, porous medium formulation with non-equilibrium sublimation was developed and validated for freeze drying without and with uniform microwave volumetric heating. The model incorporates the effect of Knudsen flow at low pressure and low permeability freeze drying. The distributed, non-equilibrium sublimation demonstrated that the sublimation front is a sharp boundary for high ice ...
Comparing Isotropic and Anisotropic Brain Conductivity Modeling: Planning Optimal Depth-Electrode Placement in White Matter for Direct Stimulation Therapy in an Epileptic Circuit
L. C. Zaragoza, B. Hondorp, M. A. Rossi
ITESM, Monterrey, Mexico
Rush Medical College, Chicago, IL, USA
Rush University Medical Center, Chicago, IL, USA
The goal of our work was to calculate a patient-specific brain conductivity map for predicting the extent to which direct stimulation therapy can strategically propagate through pathological white matter. Our laboratory developed isotropic and anisotropic human brain finite element method (FEM) models derived from SPGR magnetic resonance imaging (MRI) and diffusion tensor imaging (DTI), ...
C. Gavrila, A. Ghiaus, and I. Gruia
Technical University of Civil Engineering Bucharest, Faculty of Building Services, Bucharest, Romania
University of Bucharest, Faculty of Physics, Bucharest, Romania
A dynamic mathematical model, based on physical and transport properties and mass and energy balances, was developed for the simulation of unsteady convective drying of agricultural products (fruits and vegetables) in static bed conditions. The model utilizes water sorption isotherm equations and the change in solid density due to the shrinkage phenomenon. The aim of this article is to describe ...
A Practical Method to Model Complex Three-Dimensional Geometries with Non-Uniform Material Properties Using Image-based Design and COMSOL Multiphysics®
J. Cepeda, S. Birla, J. Subbiah, H. Thippareddi
Department of Food Science & Technology, University of Nebraska, Lincoln, NE, USA
Department of Biological Systems Engineering, University of Nebraska, Lincoln, NE, USA
Geometries with heterogeneous material properties are typically defined as a set of multiple parts, each part representing a different material. However, assembling or defining the individual parts of complex geometries can be difficult. A practical method based on image-based mesh generation, a custom algorithm for labeling materials, and interpolation functions of COMSOL Multiphysics® can be ...
P. Pattnaik, S. K. Kamilla , Debi Prasad Das
MEMS Design Center, Institute of Technical Education & Research (ITER),Siksha ‘O’ Anushandhan University, Bhubaneswar-751030, Odisha,India
Process Engineering and Instrumentation Cell,Institute of Minerals and Materials Technology (IMMT),Bhubaneswar, Odisha,India
To prevent further complications in diabetes, proper management of blood glucose levels is essential. By using ultrasonic transceivers (both transmit and receive) the glucose level of human blood can be determined. By using this ultrasonic technique miniaturized sensors for non-invasive monitoring blood glucose levels. In this paper Barium Titanate (BT) thin film was used as a transmitter and ...
J.G. Pieters, R. ElGamal, F. Ronsse
Faculty of Bioscience Engineering, Department of Biosystems Engineering, Ghent, Belgium
CFD simulations were carried out to predict the convective heat and mass transfer coefficients in the rice bed, and correlations were developed for the convective heat and mass transfer coefficients as a function of drying air flow rate. The developed correlations were used to extend the model developed by ElGamal et al. (2013) for thin-layer rice drying to volumetric heat and mass transfer in a ...
V. Nicolas[1,2], J.P. Ploteau, P. Salagnac, P. Glouannec, V. Jury, and L. Boillereaux
Laboratoire d’Ingénierie des MATériaux de Bretagne – Equipe Thermique et Energétique, Université Européenne de Bretagne, Lorient Cedex, France
Laboratoire d’Etudes des Phénomènes de Transfert et de l’Instantanéité : Agro-industrie et Bâtiment, Université de La Rochelle, La Rochelle Cedex, France
Laboratoire de Génie des Procédés, Environnement, Agroalimentaire, ENITIAA, France
In this paper, we present a first model carried out with COMSOL Multiphysics to model bread baking, considering heat and mass transfer coupled with the phenomenon of swelling. This model predicts the pressures, temperatures and water contents evolutions in the dough for different energy requests. First results obtained are analyzed according to various physical parameters in order to better ...
Improving Detection Sensitivity for Nanoscale Targets Through Combined Photonic and Plasmonic Techniques
G. Zhang, Y. Zhao
Clemson University, Clemson, SC, USA
Photonic technique such as the whispering gallery mode (WGM) is often used for detection of small particles like bacteria and viruses. It offers good detection sensitivity and is advantageous over other detection techniques because the detection can be label free. However, the detection sensitivity may not be sufficient when the size of the detection target is in nanoscale. To change this, we use ...
J.J. Dubowski, and D.Carrier
Department of Electrical and Computer Engineering, Université de Sherbrooke, Quebec, Canada
We present a Finite Element Method simulation procedure that allows rapid development of prototype devices comprising novel self-referenced interference SPR (surface plasmon resonance) biosensing microstructures. The procedure takes advantage of COMSOL Multiphysics and MATLAB software and their bi-directional link. The simulation is made using COMSOL RF Module, 2D harmonic propagation ...