アプリケーションギャラリには電気, 構造, 音響, 流体, 熱および化学分野に関連する COMSOL Multiphysics® チュートリアルおよびデモアプリファイルが用意されています. これらの例はチュートリアルモデルまたはデモアプリファイルとそれに付随する手順をダウンロードすることにより独自のシミュレーション作業の開始点として使用できます.
クイック検索機能を使用して専門分野に関連するチュートリアルやアプリを検索します. MPHファイルをダウンロードするには, ログインするか, 有効な COMSOL ライセンスに関連付けられている COMSOL Access アカウントを作成します. ここで取り上げた例の多くは COMSOL Multiphysics® ソフトウェアに組み込まれ ファイルメニューから利用できるアプリケーションライブラリからもアクセスできることに注意してください.
This model showcases how to use fibers in thin layers to model thin anisotropic composites embedded in a solid without explicitly drawing either the layer of material or the reinforcing fibers. Here, it is used to model steel cords in tire belts that are used to provide structural ... 詳細を見る
This example investigates a single cylinder reciprocating engine supported by hydrodynamic bearings. A starting torque brings the engine to the required speed, after which a load torque is applied. Following start-up, the engine operates under the action of the cylinder pressure. The ... 詳細を見る
This model is of the P.57 Type 4.3 Full-band Ear Simulator. The model includes the geometry of the ear canal as well as the pinna defined in the ITU-T P.57 standard. The model also includes interpolation data for an ear drum impedance ensuring correct acoustic properties of the ear. The ... 詳細を見る
風力タービンは, 再生可能エネルギー源としてますます人気が高まっています. そのため, 風力タービンの設計, 分析, 製造はエネルギー業界にとって重要です. タービンブレードは, 風力タービンの重要な部品です. 回転によって電力を生成する際, タービンブレードは風, 重力, 遠心力などのさまざまな負荷に耐える必要があります. ブレードのサイズが大きいため, 軽量で強度の高い材料が必要であり, 複合材料はこれに最適です. この例では, カーボンエポキシ, ガラスビニルエステル, および PVC フォームの混合物を使用して, ... 詳細を見る
This tutorial shows how to best solve full 3D vibro-electroacoustic multiphysics models of loudspeakers. The model is based on a 3D representation of the existing 2D axisymmetric Application Library model loudspeaker_driver found in the software. The setup of the physics is essentially ... 詳細を見る
This example shows how to compute thermally induced stresses in a turbine stator blade using the Thermal Stress, Solid interface. The conditions within gas turbines are extreme. The pressure can be as high as 40 bar, and the temperature more than 1000 K. Any new component must therefore ... 詳細を見る
This example shows how to compute deformations caused by secondary creep in a turbine stator blade. The creep rate is highly influenced by temperature, and the deformation and stress relaxation is thus controlled by the temperature field. 詳細を見る
In this 2D tutorial, a test sample consists on one side of an isotropic material and on the other side of a heterogeneous anisotropic material (a transverse anisotropic zinc crystal). Elastic waves in the sample are excited by a point-like force. The model is solved with the Elastic ... 詳細を見る
流体が材料やエネルギーの輸送に使用される場合, 流動する流体の速度を知ることは重要です. 流速を測定する飛行時間法または通過時間法では, 超音波信号をパイプ内の主流に伝達して, 非侵襲的に流速を測定します. 主流に対して角度を付けて信号を送信することにより, 超音波信号は主流の方向に移動する場合は音速よりも速く伝わり, 主流に逆らって移動する場合は音速よりも遅く伝わります. 2 つの方向の移動時間の差は, 主流の速度に比例して増加します. このタイプの流量計は, 特に産業環境で多くの用途があります. このチュートリアルモデルでは, COMSOL ... 詳細を見る
Interfacial failure, or delamination, in a composite material can be simulated using a cohesive zone model (CZM). A key component of a CZM is the traction-separation law, which describes softening in the cohesive zone near the delamination tip. This example demonstrates the ... 詳細を見る
